Barstool Philosophy - When Did I Become the Expert!

Every once in a while, I responsibly enjoy an "adult beverage" and ponder life. 

I call it "barstool philosophy".  

The beverage over which much
wistom is shared

Recently,  I celebrated my 51st time riding a giant rock around a "gianter" ball of fire floating in the vast expanse of space. 

Only a few days after that, I found myself helping seal the fabric envelope on a 1940s vintage  Taylorcraft. 

The Taylorcraft with fabric
over its steel tube frame

But this time "helping" meant handing the brush to someone half my age and saying, "you're up, kid".  

Somehow, when someone said, "he's the expert", and we looked around for that guy, I realized the eyes were looking at me. 

It didn't seem right. There's so much I don't know, so much I haven't done yet. 

I learned, or rather re-learned, teaching is a different mindset.

It's watching, guiding, stepping in, but not too much. It's saying, "if you do that, this bad thing will happen. Ask me how I know."

But we reached the finish-line in that milestone. The end product was pretty good 

The kids looked at me and said , "I hope we did good. "

Little do they know, the thought going through my mind was...

"I hope I did good."

So what lessons did I learn from this anecdote? \ "old guy with experience". I'm not sure when that happened. 

But happened it did. And I realized I had something to offer. While I don't know it all, the years had taught me more than I realized. Things that had become second nature by me were new, valuable lessons to those just starting out. 

Somewhere, without my realizing it happened, I became a mentor. 

I learned patience. I learned to look at a student and say, "You made this mistake. This is what you did wrong." And with a wry smile I'd say, with accurate self-deprecation, "Ask me how I know. I did it too.' 

And finally..

This post is pretty far removed from the Computer Aided Design Posts I've done in the past. My life and career has evolved. I'm not as deep in 3D modeling tools as I once was. The versions I use are old, and I don't use them at the level I did a few years go. 

But the lesson shares common ground.

For those of use who have a little more gray in our hair, and find ourselves squinting a little harder at our screens because "someone made the fonts smaller". 

Look to the fresh faced kids who were born after we graduated high school. 

You might have something to teach them. 

Why Combine Two Different Radii Fillets in One Feature? - Food for Thought for Autodesk Inventor and Fusion 360

 Once upon a time, I was asked, in reference to Autodesk Inventor and Autodesk Fusion 360, "Why would someone want to have a fillet feature with more than one radius in it?" 

An example of two different fillet radii in Fusion 360

It's a fair question. It's likely we can pick a feature in just about any CAD tool and ask, "Why is that there?"

But to that end, I did have a reason one might want to combine two different fillet radii in one feature. 

It's a matter of organization. In my design work, I often find myself modeling O-ring grooves, which nearly always have a different radius at the top and the bottom of the gland. Having the ability to combine the different radii in the same feature allows me to combine the fillets into a "O-ring Radius Feature", and maybe shave down the feature tree a little bit. 

An O-ring groove using two different radii fillets in the gland.




O-rings installed in the glands.
Just to give some context to the first image.

Another case I've used was way back when I was designing sheet metal tooling. I used it when "keying" a rectangular insert. In that example, the opening has 3 radii of one size, and the fourth is a different radius. The insert has chamfers of a similar size. This prevents the insert from being inserted in the wrong direction. Why fillets on the opening and chamfers on the insert? It was easier to machine with the tooling of the time!

An example of a sheet metal stamping insert


The"keying" feature up close. 


Admittedly, these two example are very specific to my own design experience. But perhaps it might give someone food for thought. 

While you might not run into one of these particular examples I've described, maybe there will be something similar that you can use.  

Is it life changing? Not very likely. But maybe it's a little food for thought as you make your way through the 3D CAD world. 

Drilling for Truth - Implied Drill Tolerance

First, I have to start with my big disclaimer.

While I've had experience with drawing standards, I don't consider myself a full blown expert. There is so much detail in standards, I can't say I'm an authority on all of them. 

Also, living in the United States, I work in the ANSI/ASME standards.  

My apologies to those who are living the ISO life (which is basically everyone who isn't the United States), I'm only acquainted with that standard. 

So this post will be based on "freedom units", that is feet, inches, and bald eagles. 

Joking aside, I hope this post is entertaining at least. Onward to the post. 

My current place of employment has a lot of legacy drawings. It's not uncommon to find a scanned drawing from the 1970s in our data management system.

It's like digital archeology! 

One of the things I find can be a big challenge, and very interesting, is interpreting dimensions, notes, and callouts that have fallen out of favor over the years.

Recently I was part of a discussion regarding a hole callout on one of these old drawings. 

The callout stated "Drill" and called out a specific drill size. In the case of the screen capture shown below, the drill size called out is a #30 drill, which is .1285 inches in diameter. But even the diameter is called out as a reference dimension. 


The really interesting thing about this callout is that it implies it's own tolerance, in accordance with AND10387.

The tolerances are based on the size of the drill, and a screen capture is shown here from Engineers Edge. You can even see that it has a link to AND10387




But now comes a plot twist. 
According to Everyspec, AND10387 was cancelled for new design and is only used for "replacement purposes". No new standard is shown to supersede this one. 

So what does that mean? 

I wasn't able to find a specific standard that states specifically how to handle drilled holes now. But my experience has taught me that, if required, a tolerance will be implicitly stated next to the dimension. If no tolerance is stated with the dimension, then the block tolerance will be used. 

A hole with the tolerance implicitly stated
Since AND10387 is only valid only for replacements, there's a good chance you may never see a drawing with an implied drill tolerance. But there's always a chance an old drawing will rise from the depths. So perhaps it's a good reference to keep in the archives!

And if anyone is aware of a standard that calls out standard drill tolerances, or if you just "do it another way", feel free to leave a comment.

Lessons from a Mentor, a Quarter Century Later

 Sometimes, a lesson learned from long ago comes to pass. 

Recently I was working on a project that required I transfer the location of four threaded holes to a piece of aluminum so clearance holes could be drilled. The question was, how to do it? 

Sure I could measure out the holes, but the threaded holes were t-nuts pressed into plywood, and the holes for the t-nuts were measured using a tape measure. So the hole placement was made to more of a carpentry accuracy than an aerospace tolerance. But I still wanted to keep the clearance holes as tight as practical.

A 3D model of the T-nut that was pressed into Plywood

But I remembered watching an old tool maker when I was a young engineer fresh out of college. And if you haven't guessed by the title of this post, that was about 25 years ago.... Ouch. 

He showed me a "threaded hole transfer punch". It's a small tool that stores threaded screws that look almost like set screws. However they have points in them instead of the hex that one would expect from a set screw. 

I had my solution! I placed an order with McMaster Carr for the punch I needed, and I had it in my hands the next day. 

They're screwed into the holes you need to transfer. You then position the workpiece that requires the holes, give it a quick strike with a hammer. And now you have marks where you need to drill. 

Then it's off to the drill press to drill the holes you need. 

The transfer punch tool and two of its inserts.
The inserts are stored inside the tool. 
The tool also doubles as a wrench for the inserts.

The transfer punch with two punches threaded into the T-nuts

The marks left in the aluminum from the punches.
I'm afraid I didn't get a chance to get a picture of the drilled holes.

Using the tool that old die maker showed me, in the way he showed me how to use it, I had the holes I needed in no time flat. The whole process took about fifteen minutes. And that includes walking to another building where the drill press was kept! 

That's a lot quicker than trying to match the holes by measuring it out.  

And, in a strange case of deja vu, a young intern looked over my shoulder and asked me, "How did you mark those holes?"

So it was my turn to pass along the lesson I learned 25 years ago from an old die maker about the "threaded hole transfer punch". 

Other than sharing a cool story, what's the lesson? 

I would say to look for those small mentoring moments that can sometimes come from the most unexpected places. It might be from someone on the shop floor, an analyst in the corner of that dark office, or a program manager who's "been there and done that". 

A lesson can be learned in a few minutes can take years to pay off. But when it  does, it can be a life saver! 

Wow, that lesson was twenty five years ago.... Thinking of that I'm suddenly overcome by the urge to yell at some kids to get off my lawn....

About the Author:

Jonathan Landeros is a degreed Mechanical Engineer and certified Aircraft Maintenance Techncian. He designs in Autodesk Inventor at work, and Autodesk Fusion 360 for home projects. 

For fun he cycles, snowboards, and turns wrenches on aircraft. 

Running Stress Simulations on a World War 2 Era Part

 I've been using Fusion 360 to model parts from World War 2 era parts It's a project I enjoy on the occasional evening and weekend. 

But some time ago, someone asked me, "Have you ever run a Stress Analysis Simulation on one of those parts?" 

It seemed like an interesting challenge. What would a part designed in the 1940s look like when tested with a modern Finite Element Analysis (FEA) tool. 

So I decided to fire up the Simulation module in Fusion 360, and set up a stress test to see how a component I'd modeled would hold up. 

The part I decided to use was for a P-51 Mustang, made by North American Aviation. 

The part itself is the body for a "Hydraulic Landing Gear Uplock Timing Valve". I decided I'd see how Fusion 360's simulation tools would analyze this old component. 

First, I set the material. The print listed the material as "24ST", which is a designation now obsolete. However the new equivalent is 2024. So I created that material in Fusion 360's material library, and applied it to the part. 

An excerpt from the print.
The 24ST aluminum bar can be seen in the material column

First, I needed to figure out what pressure I would be testing for. Based on the document I found here, the P-51 has a "low pressure 1000psi system". That comes out to about 69 bar in the metric system. 

For my test, I'll double that by applying a pressure of 2000 psi (138 bar). I'm using that as my burst pressure for this housing. 

As for fixing the part, I used the two mounting holes in the housing. 

With all that said and done, it was time to fire the simulation off into the cloud and wait for the results. 

All I can say that in the engineering parlance, I'd call this part "hella strong". Even at double the expected operating pressure, the minimum safety factor is about 4.5!

Assuming my analysis setup is good, the part is probably overbuilt and could be optimized to save weight. 

So why didn't the engineers at North American spend more time reducing weight? 

That I can only speculate on. 

But there are some things to consider. The body was created without the benefit of simulation tools. Add the fact North American Aviation was designing this aircraft in the middle of a war, one can probably see how not every part is optimized as much as it could be.

Add to that, the part measures about 3in x 1-1/8in x 1-5/16in (76mm x 29mm x 33mm), Even though weight is important in aircraft, optimizing this part probably wasn't a high priority considering it's small size. 

So there we have it! A P-51 Mustang part analyzed in Fusion 360. It was a fun exercise to see what stresses on this part would look like when analyzed on a modern tool!

Happy modeling! 

Jon

Acknowledgements:

P-51 Mustang print available from  AirCorps Library

P-51 Mustang picture takien at Planes of Fame Air Museum

Why I chose to use Autodesk Fusion 360

Part of a Hydraulic Valve for 
a P-51 Mustang

Recently, I was asked why I used Autodesk Fusion 360 for my side project of modeling vintage aircraft parts. Why not use Autodesk Inventor? Or Dassault Solidworks?

Sitting down one evening, I decided to take a few moments to share my thoughts. These reasons are purely my own, as one guy cranking out models on evenings and weekends. I'm not an evangelist proclaiming my choice is better than yours. It's just that, my choice. 

Also, I do pay for a Fusion 360 subscription. I chose to take advantage of one of the promotions a few years back. I know this is likely still a hot button issue for some, but in my case, I'm glad I did. I thought it was

important that I mention that, in the interests of full disclosure.

 So, why did I chose Fusion 360? 

Accessibility

 A hydraulic housing in the
Fusion 360 mobile viewer

 The first reason I chose Fusion 360 it's easy for me to get. Yes. It's as simple as that.

Even if I chose not to subscribe, there's a free version that covers most of what I would choose to do. Sure, there's a cost associated with my subscription. But my cost for a yearly subscription is less than I'd spend on a weekend snowboarding. So for me, it's worth the expense to indulge my hobby.

Sure, there are probably ways I could get an educational copy of Inventor or Solidworks. Some are probably above board, others, more "gray market". 

At least in this case, I don't have to worry about stepping on anyone's

EULA (End User license Agreement). 

Capability

As far as bang for the buck. Fusion 360 does everything I need to do, plus more.

Most of what I do is currently limited to the parts, assemblies, and drawings. I haven't delved into the manufacturing or simulation space. But it's good to know I can do it should the time come!

I have used Fusion 360 to create *stl files for 3D printing and dxf files for a waterjet (see that post here), and overall, I've been happy with the results.

One thing I really like is the way Fusion 360 models threads. More than once I've been able to 3D print a usable thread out of Fusion 360.

A 3D print created with Fusion 360.
The fitting is threaded into 3D printed threads.

Ease of Administration

I've configured installations for Autodesk Inventor, Autodesk Vault, and to a lesser degree, Solidworks. All these tools are incredibly powerful. But with that, comes a great deal of setup and configuation. Where are the templates placed? How are you configuring your data management system? When you upgrade, what's your migration strategy? What are you using for a server?

For Fusion 360, the server is on the cloud, so there's no data to move when it's time to update hardware. 

When I purchased a new laptop, I installed Fusion 360 on my new computer, logged into my account, and had instant access to all my designs.

There was no need to migrate files or remap file locations. It was already there. In about an hour's time, I was up and running.

In Summary

In conclusion there isn't much, really. 

My big reasons why I chose Fusion 360. It works for me! Does that mean it would work for you on whatever projects you're working on? Maybe, maybe not! That's for you to decide. And whichever way you decided to go, happy 3D modeling!

Using Fusion 360 to Create Parts for a B-17 Restoration

A portion of the original print used to 
create the model.

 For many years, I've created models in Fusion 360. On occasion, I've 3D printed a few of my Fusion 360 models as "desk ornaments". 

But a few weeks ago, I had a fantastic opportunity to create a model that would be used to make a part for the restoration of a B-17 Flying Fortress. 

The part was a "friction washer" for use in the throttle quadrant. And the team needed geometry that could be cut on a water jet.

It started with a reproduction of the original Boeing print. Having the original dimensions made the modeling easy. It was interesting to note that even though standards have changed in the nearly 80 years since that print was created, it's not too different from the prints I work with today. 

The model of the friction washer, created in 
Fusion 360

Next, was to place the view on a drawing. The first goal was to dimension the drawing as a way of verifying all the dimensions were correct. Second, the drawing is what creates the 2D DXF file for the water jet. 

Once the drawing is created, delete any information that isn't required for the waterjet. This includes borders, title blocks, dimensions, centerlines and centermarks, etc. You might even consider creating a second page in the drawing for this purpose. 

Also, make sure to save the drawing before you export. I learned the hard way when I realized that the first file I exported still had all that extra geometry. Save the file before export!

The dxf geometry sent to the waterjet

Once I recovered from my snag. I sent the files off to my colleague for cutting. 

A few days later, we had our part and it fit perfectly, making for a very satisfying little journey. 

And while this little project was well worth a victory lap, there were three minor challenges that are worth mentioning. 

1) Drawing standards have changed over the decades, and while the drawing wasn't hard to interpret, some information wasn't where I'd expect it to be. Modern 3D modelers have spoiled us. We can "slap down" a new view in seconds. For the drafters of old? Adding the simplest view would take minutes. A more complicated one? Hours. 

The number of views was kept to a minimum. A part of single thickness, such as this one, will likely have the thickness dimension called out in a note. 

2) Not only have drawing standards changed, industry standards have changed. That material specification called out in 1943? It's been long superseded by a new standard. It's even possible that the standard that superseded the 1943 standard has, in turn, been superseded itself. 

Be prepared to spend a few minutes Googling the updated standards. Thank goodness for the internet! 

3) Finally, how does one interpret the tolerances called out on the drawing? Symmetric, +/-.005 for example, is easy. Model to the nominal. But what about a tolerance such as +.010/-.000? Do you "split the difference"? Do you aim for nominal? 

In my case, I decided to aim for the dimension as it was called out on the print. I figured that was the target dimension, after all. 

And in my case. It worked! Fusion 360 gave me an excellent dxf file that the waterjet used with no issuee, and the part fit perfectly into its intended position.  

It was a wonderful opportunity to contribute to a restoration. And a wonderful learning opportunity!

Acknowledgements

Print Reproduction via my Aircorps Library Subscription

Models and drawings created in Autodesk Fusion 360

My Tool Won't Fit! A Design Lesson From Life.

A typical aircraft brake disk.
There's not much room for a socket!

Hands on experience is often the greatest teacher. 

And, while helping work on a friend's change tires on a light aircraft. 

In looking at the brake disk, bolted to the tire rim, I saw that there was no way one could get a socket, the ideal tool for the job, onto the bolt. 

Fortunately, my friend, having run into this case many times before, had a wrench he'd cut to fit inside the disk. So in the end, it was job that was still very easily accomplished. 

But there lies a lesson for those of who sit behind a desk and design the machines we use every day. 

Just because the fastener fits, doesn't mean the tool will! So when designing, think of ease of maintenance. 

The maintainers, who are sometimes your customers, will thank you for it! 

About the Author:

Jonathan Landeros is a degreed Mechanical Engineer and certified Aircraft Maintenance Techncian. He designs in Autodesk Inventor at work, and Autodesk Fusion 360 for home projects. 

For fun he cycles, snowboards, and turns wrenches on aircraft. 

All PLA Prints the Same, Right? WRONG!

I print a lot of Polylactic Acid (PLA) in the 3D printer at work. I've found it's a great material to work with. It prints easy, and generally gives great results. 

A sample of a different PLA print. 
Usually a great material to work with.
Sorry, the actual print is proprietary.

Almost without exception, I have great results.

At least until all of a sudden I start having problems with it! 

When printing new color, silver from Amazon the PLA started peeling off the bed. 

It didn't matter how much glue I put down on the bed, It would peel up after a few layers. 

So what to do? 

My first step was to try a few troubleshooting steps. 

First, I raised the temperature of the bed from 50 degrees Celsius to 55 degrees Celsius. No luck there. 

Next, a thorough cleaning of the bed with isopropyl alcohol. I definitely had a cleaner bed, but still, the problem persisted.

Finally, I found a trick that solved the problem. Move the nozzle .05mm closer to the bed. Success!

The Z setting adjustment in my slicer.
I moved the nozzle slightly closer to the bed.

What is it about the silver filament? I'm not sure. But during my troubleshooting, I did notice that the gray filament did appear to be laying down a thinner layer. 

My only guess is something with the dye used to color the filament. But that's just a wild guess. 

So what's the takeaway? 

Keep an eye on those layers, and remember that not all filament of the same material prints the same! 

Resources used for this post: 

3D Printer: Fusion3 F400

Filament: Amazon Essentials Silver

Slicer Software: Simplify3D

About the Author:

Jonathan Landeros is a degreed Mechanical Engineer and certified Aircraft Maintenance Techncian. He designs in Autodesk Inventor at work, and Autodesk Fusion 360 for home projects. 

For fun he cycles, snowboards, and turns wrenches on aircraft. 

So Solidworks Happened at Work Today - A Musing

I've spent just over 20 years working with 3D CAD programs. That experience has been nearly exclusively with the Autodesk manufacturing product line, starting with Mechanical Desktop (shortly after the earth cooled), and followed by Autodesk Inventor. 

We've all seen the ubiquitous, 3D model, floating in space.

A couple of years ago, my company decided to experiment with switching to Siemens NX.

That experiment, unfortunately, failed. Siemens NX, while a good program, wasn't the right program for the needs of my employer. 

A few months ago, my company announced that we would be going to Solidworks. 

Other than dabbling in it a few times, I've never touched Solidworks. This could be an enormous change for me. 

Or not, perhaps? 

CAD Tools - Is it just
a Virtual Toolbox?

I completed an abridged "transfer training", where we were shown where all the buttons were and how Solidworks ticks. After that, we were released upon the world. 

And what did I find? Were my eyes opened to a brand new world? Was Solidworks so much better that I wondered what I was missing? 

Did I wail and gnash my teeth because Inventor was far better and I was being forced to use this inferior product?

No. I left that training and thought, "Wow! They're really similar." 

Sure, Solidworks has an Extrude and and Extrude Cut button, while Inventor has the same options combined within one Extrude command. But they both add and remove material in the end. 

There's functions where I think Inventor has it down better, and others where I have to give it to Solidworks. 

In the end, I see it as an opportunity to learn a new skill, enrichen myself, and be more marketable in a competitive world. I think that's going to take me further in the long run. 

So I suppose the point of my writing this is to muse about how CAD programs are tools. They're not the endgame, there the means to create our designs, drawings, and help us build our products. 

And there's nothing wrong with learning a new set of tools. It can only make me a more marketable designer. 

One Final Note. 

If you're using Fusion 360, you can change your Pan, Zoom, Orbit shortcuts to reflect Inventor or Solidworks, among other programs? 

I've switched mine to Solidworks, it may not be the same as having Solidworks at home, but it does makes it easier when I switch from one to the other at work! 

The Pan, Zoom, and Orbit options in Fusion 360

 

The Chamfer Note. Does It Say What You Mean?

Many CAD tools contain a chamfer note that I would describe as a leader style. 

You've probably seen it, probably used it even. 

It utilizes a leader to point at the chamfer, and contains both the chamfer distance, and angle in one simple note.

The advantage of this style is it's compact, easy to read, and especially easy to place when the chamfer is packed into a crowd with other nearby dimensions. 

But this dimensioning style as a subtle disadvantage. This style of dimension doesn't identify the direction of the chamfer. So if the chamfer angle is something other than 45 degrees, the angle direction is open to interpretation. 

Even though the chamfers are different, the callout is is the same. 
It's also correct in both cases.

That literally means that a chamfer in either dimension meets the print. That can cause confusion, and possibly "heated debates" when a parts acceptance or rejection hangs in the balance. 

The other option is to call out the chamfer distance and angle as separate, distinct dimensions.  This identifies the direction of the chamfer much more clearly.  

Of course everything is a trade off, and this method does take a little more room on the page than the leader style. Even on the image above, you can see that the page is a bit more cluttered, and someitmes a detail view is required to ensure all dimensions can be clearly seen. 

In the end, I find I use both. The leader style is used for 45 degree chamfers, since there isn't really an angle direction to speak of. However, when the chamfer is an angle other than 45 degrees, it's time to employ the explicit style, and make sure the direction is clearly shown. 

Ultimately, it's up to you which chamfer style you use. Perhaps you have the advantage of tribal knowledge to correctly identify these features. Or you have other means to make sure the chamfer is cut the correct way. 

If anything, this is a good practice hailing from the time when "back to the drawing board" was a much more literal statement! 

About the Author:

Jonathan Landeros is a degreed Mechanical Engineer and certified Aircraft Maintenance Techncian. He designs in Autodesk Inventor at work, and Autodesk Fusion 360 for home projects. 

For fun he cycles, snowboards, and turns wrenches on aircraft. 

New in Fusion 360 - Improved Thread Notes

 Sometimes it's the little things that make a guy happy. 

A thread note placed
on an external thread

In this case, it's the improved thread annotation tool in the January/February Fusion 360 update. 

In short, Fusion 360 can now create an annotation for a thread note placed with the thread tool, not just the hole tool as was the case in previous updates 

That opens up the field to place thread notes onto external features. It's a capability I've personally been hoping would get added for some time. 

Admittedly, applications like Inventor have been doing this for what seems like eons, so it's hardly a "ground-breaking" feature. 

But it sure is a nice feature to have! 

All you have to do is place the note using the "Hole and Thread Note" command, and you're off and annotating. 

Locating the "Hole and Thread Note" tool

One little cool thing I noticed in my evening of poking about. 

The tool works with threads created using the "modeled' setting too! 

A modeled thread with a thread note.

I've been waiting for this enhancement for a while! I'm glad it's finally here! 

About the Author:

Jonathan Landeros is a degreed Mechanical Engineer and certified Aircraft Maintenance Techncian. He designs in Autodesk Inventor at work, and Autodesk Fusion 360 for home projects. 

For fun he cycles, snowboards, and turns wrenches on aircraft. 

A Milestone Creating a Fusion 360 Title Block!

I have completed the task I challenged myself with in my previous post. I finished up my reproduction of a 1940s era North American Aviation title block in Autodesk Fusion 360!

The original, and Fusion 360 Title block together

It was a little tedious at times, it's a lot of repetitive sketching geometry and inserting text and properties. 

But it's completed, and ready for use. I'm sure I'll find a few more things to adjust as I test it out. 

Ultimately, I was able to recreate nearly every feature of the title block. It's not an exact match. I couldn't find a solid fill to block out the box above the part number for example. But it is close, and it will serve it's purpose just fine. 

As more features get added to Fusion 360, I'll update the title block accordingly. 

The North American Aviation tile block finished

So now, it's time to start creating drawings! From there, I'll learn more lessons and make more adjustments!

Credits:

Title Block Sourced from my Aircorps Library subscription.

About the Author:

Jonathan Landeros is a degreed Mechanical Engineer and certified Aircraft Maintenance Techncian. He designs in Autodesk Inventor, Siemens NX, at work, and Autodesk Fusion 360 for home projects. 

For fun he cycles, snowboards, and turns wrenches on aircraft. 

A Trick - Creating Fusion 360 Title Blocks from an Image

 Happy 2022! Here's to hoping for a prosperous loop around the sun. 

One of my latest endeavors has been recreating 1940s aviation prints as 3D models in Fusion 360. The drawings are available via my Aircorps Library subscription, and they're a great look into how parts and assemblies were documented nearly 100 years ago. 

A piston for an actuator on a North American P-51 Mustang.
Model created in Autodesk Fusion 360

The models are the fun part for sure, but I also decided to recreate the drawings themselves too. 

The first part of recreating the drawing, is to recreate the title block of course. 

The title block image, ready for import into Fusion 360

\

It's still a work in progress, but I thought I'd spare a moment to document my progress.

It almost goes without saying, the process can be tedious. Since the original drawings are hand drawn, they have to be recreated from scratch. 

The thought of trying to "eyeball" the title block wasn't very appealing, but finally an idea dawned on me that made the process much less challenging. 

I imported an image of the title block, scaled it to a suitable size, and laid out the geometry on top of the image.

The title block in Fusion 360. The lines sketched in Fusion 360 are highlighted.

Overall, I felt pretty well. But there was one thing I did have to overcome

There's no image opacity setting like there are in other parts of Fusion 360. But I was able to see where my sketched lines were by highlighting them. I also extended the lines beyond the edges of the image. I can always trim them later. 

Finally, I'd also use the good old, "Delete, Inspect, Undo" trick by deleting the image, inspecting, and undoing the delete.

Overall, its working pretty well. I've found the process is much faster, accurate, and less frustrating than trying to scale by using the title block in a separate window. 

As I said earlier, it's a work in progress.  I'll share my final product when I'm done. Give me time, it might be a while! This is an "evening here and there" project! 

One Final Note

The team at Aircorps Library have done a spectacular job collecting, scanning, and sharing these vintage documents. Out of respect for their work, I won't be sharing any documents or models. Please, don't ask me to do so.

If you are really interested in their documentation, feel free to check out their site and investigate a subscription yourself! 

About the Author:

Jonathan Landeros is a degreed Mechanical Engineer and certified Aircraft Maintenance Techncian. He designs in Autodesk Inventor, Siemens NX, at work, and Autodesk Fusion 360 for home projects. 

For fun he cycles, snowboards, and turns wrenches on aircraft.